|
Nominal impedance in electrical engineering and audio engineering refers to the approximate designed impedance of an electrical circuit or device. The term is applied in a number of different fields, most often being encountered in respect of: *The nominal value of the characteristic impedance of a cable or other form of transmission line. *The nominal value of the input, output or image impedance of a port of a network, especially a network intended for use with a transmission line, such as filters, equalisers and amplifiers. *The nominal value of the input impedance of a radio frequency antenna The actual impedance may vary quite considerably from the nominal figure with changes in frequency. In the case of cables and other transmission lines, there is also variation along the length of the cable, if it is not properly terminated. It is usual practice to speak of nominal impedance as if it were a constant resistance,〔Maslin, p.78〕 that is, it is invariant with frequency and has a zero reactive component, despite this often being far from the case. Depending on the field of application, nominal impedance is implicitly referring to a specific point on the frequency response of the circuit under consideration. This may be at low-frequency, mid-band or some other point and specific applications are discussed in the sections below.〔Graf, p.506.〕 In most applications, there are a number of values of nominal impedance that are recognised as being standard. The nominal impedance of a component or circuit is often assigned one of these standard values, regardless of whether the measured impedance exactly corresponds to it. The item is assigned the nearest standard value. == 600 Ω == Nominal impedance first started to be specified in the early days of telecommunications. At first amplifiers were not available and when they did become available they were expensive. It was consequently necessary to achieve maximum power transfer from the cable at the receiving end in order to maximise the lengths of cables that could be installed. It also became apparent that reflections on the transmission line would severely limit the bandwidth that could be used or the distance that it was practicable to transmit. Matching equipment impedance to the characteristic impedance of the cable reduces reflections (and they are eliminated altogether if the match is perfect) and power transfer is maximised. To this end, all cables and equipment started to be specified to a standard nominal impedance. The earliest, and still the most widespread, standard is 600 Ω, originally used for telephony. It has to be said that the choice of this figure had more to do with the way telephones were interfaced into the local exchange than any characteristic of the local telephone cable. Telephones (old style analogue telephones) connect to the exchange through twisted pair cabling. Each leg of the pair is connected to a relay coil which detect the signalling on the line (dialling, handset off-hook etc.). The other end of one coil is connected to a supply voltage and the second coil is connected to ground. A telephone exchange relay coil is around 300 Ω so the two of them together are terminating the line in 600 Ω.〔Schmitt, pp.301–302.〕 The wiring to the subscriber in telephone networks is generally done in twisted pair cable. Its impedance at audio frequencies, and especially at the more restricted telephone band frequencies, is far from constant. It is possible to manufacture this kind of cable to have a 600 Ω characteristic impedance but it will only be this value at one specific frequency. This might be quoted as a nominal 600 Ω impedance at 800 Hz or 1 kHz. Below this frequency the characteristic impedance rapidly rises and becomes more and more dominated by the ohmic resistance of the cable as the frequency falls. At the bottom of the audio band the impedance can be several tens of kilohms. On the other hand, at high frequency in the MHz region, the characteristic impedance flattens out to something almost constant. The reason for this response is explained at primary line constants.〔Schmitt, p.301.〕 Local area networks (LANs) commonly use a similar kind of twisted pair cable, but screened and manufactured to tighter tolerances than is necessary for telephony. Even though it has a very similar impedance to telephone cable, the nominal impedance is rated at 100 Ω. This is because the LAN data is in a higher frequency band where the characteristic impedance is substantially flat and mostly resistive.〔 Standardisation of line nominal impedance led to two-port networks such as filters being designed to a matching nominal impedance. The nominal impedance of low-pass symmetrical T- or Pi-filter sections (or more generally, image filter sections) is defined as the limit of the filter image impedance as the frequency approaches zero and is given by, : where ''L'' and ''C'' are as defined in constant k filter. As can be seen from the expression, this impedance is purely resistive. This filter transformed to a band-pass filter will have an impedance equal to the nominal impedance at resonance rather than low frequency. This nominal impedance of filters will generally be the same as the nominal impedance of the circuit or cable that the filter is working into.〔Bird, pp.564, 569.〕 While 600 Ω is an almost universal standard in telephony for local presentation at customer's premises from the exchange, for long distance transmission on trunk lines between exchanges other standard nominal impedances are used and are usually lower, such as 150 Ω.〔Whitaker, p.115.〕 抄文引用元・出典: フリー百科事典『 ウィキペディア（Wikipedia）』 ■ウィキペディアで「Nominal impedance」の詳細全文を読む スポンサード リンク
|